TeSys T is a green motor management system with unique power monitoring capabilities for better energy management. TeSys T carries all appropriate and necessary third party certifications. To get detailed information about TeSys T, visit our website at www. TeSys T detailed functionalities and possible configuration:. These communication protocols allow the TeSys T controller to integrate seamlessly into your automation systems.
A motor managed by a TeSys T controller can be controlled:. Each listed mode is available as 2 or 3 wire control. A custom mode is available to allow the user to create a specific motor control mode that is not predefined in the controller.
Custom Logic has the basic functions of a small programmable logic controller PLC. To ensure consistency, the same software used to commission the TeSys T controller is used for Custom Logic programming. Statistical and diagnostic functions:.
TeSys T controller is a flexible motor management system using the SoMove commissioning tool. See Components for details. Control Voltage V.
The controller is the central component in the motor management system. It manages the basic functions such as:. Magelis Display. The expansion module adds the following functionalities to the TeSys T controller:. Depending on the application, two types of HMI can be used with the motor management system. Local control of the motor via the local control interface keys can be customized. A language download utility LangTool , together with all the other languages, are available on the website www.
Two applications have been predefined for the TeSys T controller. Depending on the application loaded, the HMI terminal makes it possible to:. Current Transformer Ratio [1]. Shunting During Starting Period.
For a nonautomatically started motor, the overload protection shall be permitted to be shunted or cut out of the circuit during the starting period of the motor if the device by which FPO the overload protection is shunted or cut out cannot be left in the starting position and if fuses or inverse time circuit breakers rated or set at not over percent of the full-load current of the motor are so located in the circuit as to be operative during the starting period of the motor.
The motor overload protection shall not be shunted or cut out during the starting period if the motor is automatically started. The motor overload protection shall be permitted to be shunted or cut out during the starting period on an automatically started motor where: 1 The motor starting period exceeds the time delay of available motor overload protective devices, and 2 Listed means are provided to: a.
Sense motor rotation and to automatically prevent the shunting or cut out in the event that the motor fails to start, and b. Limit the time of overload protection shunting FPO or cut out to less than the locked rotor time rating of the protected motor, and c. Provide for shutdown and manual restart if motor running condition is not reached. Figures 1 and 2 show possible circuits for use in conjunction with 3-wire control schemes.
Figure 1 complies with NEC requirements. Figure 2 exceeds NEC requirements, but the additional safety provided by the zero speed switch might be desirable. UL or other listed devices must be used in this arrangement. Used for large VA coils only. Contact convertible. Instantaneous 3 N.
Instantaneous 2 N. On Delay, 1 N. Off Delay, 1 N. Terminals digits — odd for line side terminals and even for load side terminals. Alarm Contact N. Alarm Contact 14 22 32 44 54 Auxiliary contacts on contactors, relays and push button contacts Overload contact terminals are marked with two digits. The first use 2-digit terminal designations, as shown in the diagram above. If the device has a non-isolated second digit indicates the status of the contacts, N.
Short-Circuit Protection Rating of branch circuit protective device must comply with applicable electrical codes and the following limitations: Type of Device Max. If starter is used on lower voltage, connect per coil diagram. Voltage between line side conductors must not exceed line-to-line voltage rating of contactor. Vload must not exceed volts-per-load rating of LOAD contactor. Line current carried by any contact must not LOAD exceed ampere rating of contactor.
B— B1 [3] Semiconductor fuses. B1 [3] Semiconductor fuses. To prevent output switching capability, damage, all switches except therefore leakage current is not emitters must have load applicable. Thru-beam emitter is connected to switch. To prevent damage, all therefore it requires only a 2-wire switches except emitters must cable connected directly across have load connected to switch.
Thru-beam emitter draws a maximum of 45 mA. Output current Value of Load R max. Connect minus - terminal to load. Housing must be connected to minus.
Housing switch. The voltage drop across each switch must be grounded for proper operation. OG - dark prog. XEN P, N. Both devices at max. Both devices at min. Connections shown are for common control. If motor line voltage is different from voltage rating stamped on alternator coil terminals, alternator must be connected to motor lines thru control transformers.
Control circuit conductors require overcurrent protection in accordance with applicable electrical codes. JCK 60 is AC only. Polarity markings are for DC units only. Applying power to terminal 7 or jumpering from terminal 5 to 7 Control Power through an external contact initiates the timer. LC2D [8]. Check with local sales office for availability. For the best experience of this site, please enable Javascript for the www. Includes mechanical interlock without electrical contacts.
Installer to complete wiring for electronically interlocking contactor operating coils by using a N. Includes mechanical interlock LA9D with prewired electrical contacts for interlocking contactor operating coils. Was this helpful? Yes No. Tell us why! LC1D09 AC coil only. LC1D12 AC coil only.
0コメント